What is Balboa control system?
The Value Series (VS) family of hot tub control systems were designed using Balboa’s patented M7 temperature and flow sensor technology and a new universal control platform. These features increase the reliability, ease of installation and serviceability of the control.
How do I reset my Balboa hot tub control panel?
You can reset a hot tub control panel by switching it off, waiting for between 10 and 20 seconds and then switching it back on again. If the error signal continues on the control panel then you will need to consult your hot tub manual to see what the problem is.
How do I reset the high limit switch on my hot tub?
The High Limit Switch Needs to Be Reset or Replaced Occasionally, the high limit switch will trip when you’re filling your spa. Or it might need a reset from time to time for no known or serious reason. Simply reset by pressing the big red button on your spa pack. The high limit switch may be housed in a thermowell.
How do you program a Balboa hot tub?
To program, press “Temp,” then “Jets 1.” Press “Temp” to adjust. Press “Jets 1” to exit programming. For non-circ systems, low-speed pump 1 and the ozone generator (if installed) run during filtration. For 24 hour circulation systems, the circ pump and the ozone generator (if installed) run 24 hours.
How do you change the mode on a Balboa hot tub?
Balboa Controller VS500Z and VS501Z Mode Settings for Standard, Economy and Sleep. Mode is changed by pressing the Temp or Set button, and then pressing the Light button. If there are UP and DOWN buttons, use the UP button. Do not press the buttons at the same time.
Where is the reset button on my hot tub?
Locate the spa’s high-limit reset. This is a red button found on many spa packs. It may be located on the heater and covered by a rubber nipple.
What does SL mean on a Balboa hot tub?
sleep mode
While your hot tub is in sleep mode (or ‘SL’ & SLP mode on some models), the jets will operate occasionally to filter the water. In sleep mode, your hot tub’s heater will usually only kick on once the temperature dips below 20 degrees of the set temperature.
Where is the control panel on a hot tub?
The topside control panel is the name for the display and controls, on the top-side of the spa, or where you can see them when you’re in the spa. I’m old enough to remember having to get out of the spa to turn up the heater or turn on the air blower, or those sticky hexagonal air buttons.
Where is the reset button on a hot tub?
Do you need a Balboa spa control system?
Balboa Direct provides cutting edge, reliable, high value control systems that Balboa Water Group has been known for. Whether you are looking to purchase a retrofit kit, a Balboa spa control system, or need replacement parts on your existing spa control system, you can buy with confidences knowing that Balboa has the right system pack for you.
Where can I find the Balboa direct instruction manual?
54515-01, GS5-GS501SZ-RCA-3.0. 54848, GS5-GS525Z-RCA-3.0K. If you are having trouble reading any file contained on this page, you may need to update your PDF viewer. Click on the image below to open a new browser window and visit the Adobe website:
How does a Balboa direct water heater work?
The two sensors located within the heater housing compare the inlet water temperature with the outlet water temperature. It works no matter which direction the water flows through the heater.
What kind of screwdriver does Balboa 50A use?
UÊAmmeter (50A) UÊBalboa Six-in-one Screwdriver UÊDigital Multi-meter UÊPadlock (to lock electrical disconnect during service) UÊPliers: Slip Joint & Needle nose Recommended Parts For Service Calls UÊExtra Board(s) UÊExtra Panel(s) UÊFuses UÊJumpers UÊHeater Assembly 20618 JUMPER LOGIC COMMON FUSES USED