How many gallons per hour does a 1/3 HP sump pump?

Prevent Basement Flooding With a Submersible Sump Pump A 1/3-horsepower motor collects and moves up to 42 gallons per minute (GPM) of water away from your home. The impeller, the device that pulls the water in, has a reliable nonclogging design that will continue to process overflow — even during severe storms.

Is 1 3 HP sump pump enough?

For most average-sized homes in areas with average water tables, a 1/3 HP sump pump should be sufficient. Typically, 1/3 HP pumps can handle 7′ – 10′ vertical lifts from the sump pit if they have one 90-degree elbow and a horizontal pipe run between 3 feet and 25 feet.

How far can a 1/3 HP sump pump push water?

A 1/3 HP sump pump can handle 7 to 10 feet vertical lift off the sump pump, a 90-degree elbow and a horizontal pipe running between 3 and 25 feet.

What is the difference between a 1/3 and 1/2 HP sump pump?

A 1/3 horsepower sump pump is the standard and gets the job done, but for basements with heavier flooding, a 1/2 horsepower removes around 3,000 gallons of water per hour. If you’re on a budget, a . 25hp pump will work if you don’t find a large sump pump necessary for your home.

How many GPH is a 1/2 HP sump pump?

4400 GPH
1/2 HP Submersible Sump Pump with Heavy Duty Vertical Float Switch 4400 GPH.

How many GPH is a 1 hp pump?

52 GPM
From this chart, you can see that a 1 horsepower pump (the green curve) will give you 52 GPM flow on a system with 64 feet of head.

How high can a 1/2 HP pump push water?

A two-line jet pump can typically raise water from depths of 30-feet to 80-feet, and at water delivery rates of 4 gpm (gallons per minute) (for a 1/2 hp 2-line jet pump serving an 80 foot deep well) to 16 gpm (for a 1 hp 2-line jet pump serving a 30 foot deep well).

Will bleach damage a sump pump?

Because the bleach has been significantly diluted with water, solution that is not fully pumped out of the basin does not damage your sump pump. Sump pumps made of cast iron or thermoplastic are able to be safely cleaned using bleach.

Can a sump pump be too powerful?

You don’t want a pump that is either too small or too powerful. If the pump is too small, it won’t be able to keep up with water flowing into the basin. If the pump is too powerful, it will “short cycle.” This means the pump will start and stop frequently, which can cause premature pump failure.

How deep can a 1/2 HP well pump go?

2½” – Jet pumps in shallow well applications (depth less than 25 feet) should be installed using 1¼” suction piping with a foot valve. 4″ – Convertible jet pumps used in deep well applications (depth greater than 25 feet) and deep well submersible pumps.

How high can a 1 hp pump push water?

How high can a 1hp pump lift water? The water will boil due to low pressure. The farthest you can suck up water is about 30 ft. The specs indicate that it can pull water up 26 ft.

Can I replace my 1 HP pool pump with a 1.5 HP?

So to answer the question, yes, you can replace your 1hp pool pump with a 1.5hp pool pump, but only if your situation calls for it. This will provide the flow that is needed to circulate your pool water properly and save you from high electricity bills at the same time.

Which is the best sump pump discharge hose?

This heavy-duty pool backwash hose features a molded fiberglass body, an eight-foot flexible hose, and durable PVC material. . WAYNE 56171 1.25 In. Sump Pump Discharge 24 ft. Hose Kit With Clamps

How tall does a sump pump pipe have to be?

I have a 1/3 hp submersible pump. can I have the pipe going up about 7 feet, then traveling about 60 feet to the other side of the house, the go up about 8 inches, change direction then go about another 12 feet to get out of the house? The end result is that I want both pits to empty in the same “New” place.

Which is the best cast iron sump pump?

The 92341 offers a powerful, yet energy efficient (4.1 Amp) thermally protected motor for longer life and durability. The pump features a stainless steel impeller, 1-1/2 in. FIP discharge and 10 ft., replaceable, water proof power cord.

How to calculate the sump pump discharge length?

Friction in the pipe and the fittings is also expressed as ‘head’, so you need to calculate that as well. Let’s say you will use 75′ of 1-1/2″ PVC pipe and 4 90° elbows… At TEN GPM 100′ of 1-1/2″ pipe has a bit less than 1′ head. At TWENTY GPM the same pipe has a bit less than 3′ head.